A filament producer in Malaysia ordered a PLA ABS PETG TPU 3D printer filament extruder machine from Friend Plastic Machine — the CE certified FLD-45 single screw line — to replace toll-produced filament with in-house production. The brief was unusual in one respect: the client wanted one machine, four polymers. PLA, ABS, PETG and TPU all had to run on the same 45 mm extruder with no screw change, only a die and temperature recipe change. The line was built, trial-run on the customer's own resins in our Zhangjiagang workshop, shipped in 30 working days, and has been running three polymer families commercially since commissioning, with TPU added in the third month.
The buyer supplies 1.75 mm filament to Malaysian 3D printing service bureaus, school STEM programmes and a growing base of industrial users in Johor and Selangor. Sourcing finished filament from third-party extruders gave them 4–6 week lead times, no control over batch-to-batch diameter, and no short colour campaigns for local resellers. Their target was an in-house line that could switch between commodity materials in a single shift.
Malaysia's year-round humidity is unforgiving to hygroscopic polymers, so moisture control rather than line speed became the decisive issue.
| Material | Barrel Temperature | Pre-drying | Practical Output |
|---|---|---|---|
| PLA | 190–210 °C | 45 °C / 4 h | 20–22 kg/h |
| ABS | 230–250 °C | 75 °C / 4 h | 19–21 kg/h |
| PETG | 235–250 °C | 65 °C / 5 h | 18–20 kg/h |
| TPU (95A) | 195–215 °C | 80 °C / 4 h | 12–15 kg/h |
All four materials had to hold 1.75 mm ±0.03 mm, because the client's service-bureau customers print on both Bowden and direct-drive machines where diameter drift shows up immediately as under-extrusion or jams. TPU set the hardest constraint: soft pellets feed unevenly, generate more die swell, and need gentler screw compression and tighter haul-off control than rigid polymers.
A Friend commissioning engineer spent eight days on site in Malaysia. The first three days were mechanical: levelling the 17 m line, setting die and calibration gaps, and establishing stable haul-off tension. The remaining days were dedicated to material trials, working through the four polymers in sequence so the client's operators could see how the same line responds differently to each one:
| Metric | Requirement | Result |
|---|---|---|
| Materials on one line | PLA, ABS, PETG, TPU | All four running commercially |
| Output on PLA | 20 kg/h | 20–22 kg/h |
| Output on TPU | Usable commercial rate | 12–15 kg/h, stable |
| Diameter tolerance | 1.75 mm ±0.03 mm | ±0.02–0.03 mm on all four polymers |
| Material changeover | Same shift | Under 60 minutes including purge |
| Batch consistency | Reduce customer complaints | No diameter-related rejections in first six months |
Within six months the client had moved roughly 70 % of their filament volume in house, run two short colour campaigns without an outside extruder, and added a TPU line they had never been able to source reliably.
A multi-material filament line only works if the screw, cooling length, haul-off and drying stage are sized for the most difficult polymer in the recipe — in this case TPU — not for PLA alone. If you are evaluating a PLA, ABS, PETG or TPU 3D printer filament extruder machine for your own market, send us your material list, target diameter and available floor length, and our engineers will propose a configuration and a material trial plan built around your resins.
A filament producer in Malaysia ordered a PLA ABS PETG TPU 3D printer filament extruder machine from Friend Plastic Machine — the CE certified FLD-45 single screw line — to replace toll-produced filament with in-house production. The brief was unusual in one respect: the client wanted one machine, four polymers. PLA, ABS, PETG and TPU all had to run on the same 45 mm extruder with no screw change, only a die and temperature recipe change. The line was built, trial-run on the customer's own resins in our Zhangjiagang workshop, shipped in 30 working days, and has been running three polymer families commercially since commissioning, with TPU added in the third month.
The buyer supplies 1.75 mm filament to Malaysian 3D printing service bureaus, school STEM programmes and a growing base of industrial users in Johor and Selangor. Sourcing finished filament from third-party extruders gave them 4–6 week lead times, no control over batch-to-batch diameter, and no short colour campaigns for local resellers. Their target was an in-house line that could switch between commodity materials in a single shift.
Malaysia's year-round humidity is unforgiving to hygroscopic polymers, so moisture control rather than line speed became the decisive issue.
| Material | Barrel Temperature | Pre-drying | Practical Output |
|---|---|---|---|
| PLA | 190–210 °C | 45 °C / 4 h | 20–22 kg/h |
| ABS | 230–250 °C | 75 °C / 4 h | 19–21 kg/h |
| PETG | 235–250 °C | 65 °C / 5 h | 18–20 kg/h |
| TPU (95A) | 195–215 °C | 80 °C / 4 h | 12–15 kg/h |
All four materials had to hold 1.75 mm ±0.03 mm, because the client's service-bureau customers print on both Bowden and direct-drive machines where diameter drift shows up immediately as under-extrusion or jams. TPU set the hardest constraint: soft pellets feed unevenly, generate more die swell, and need gentler screw compression and tighter haul-off control than rigid polymers.
A Friend commissioning engineer spent eight days on site in Malaysia. The first three days were mechanical: levelling the 17 m line, setting die and calibration gaps, and establishing stable haul-off tension. The remaining days were dedicated to material trials, working through the four polymers in sequence so the client's operators could see how the same line responds differently to each one:
| Metric | Requirement | Result |
|---|---|---|
| Materials on one line | PLA, ABS, PETG, TPU | All four running commercially |
| Output on PLA | 20 kg/h | 20–22 kg/h |
| Output on TPU | Usable commercial rate | 12–15 kg/h, stable |
| Diameter tolerance | 1.75 mm ±0.03 mm | ±0.02–0.03 mm on all four polymers |
| Material changeover | Same shift | Under 60 minutes including purge |
| Batch consistency | Reduce customer complaints | No diameter-related rejections in first six months |
Within six months the client had moved roughly 70 % of their filament volume in house, run two short colour campaigns without an outside extruder, and added a TPU line they had never been able to source reliably.
A multi-material filament line only works if the screw, cooling length, haul-off and drying stage are sized for the most difficult polymer in the recipe — in this case TPU — not for PLA alone. If you are evaluating a PLA, ABS, PETG or TPU 3D printer filament extruder machine for your own market, send us your material list, target diameter and available floor length, and our engineers will propose a configuration and a material trial plan built around your resins.